A novel clock generation algorithm for system-on-chip based on least common multiple

Due to increase in the number of Intellectual Property (IP) cores, clock generation in current day System-on-Chips (SoCs) is facing a crisis. The conventional method of using a dedicated Phase Locked Loop (PLL) to generate the clock for each IP core is becoming inefficient in terms of power and cost. We propose an algorithm based on Least Common Multiple (LCM) to minimize the number of PLLs required to generate the clocks for the IP cores in a SoC. This is done by finding an Optimum Operating Frequency (OOF) for each IP core within 10% below the maximum operating frequency of the core. The OOF is chosen such that the LCM of the OOF of all the IP cores is minimized. Simulated annealing is used to find the LCM. This LCM is the crucial high frequency from which maximum number of clocks can be derived by clock dividers.     

Morphologies and dynamic mechanical properties of core‐shell emulsifier‐free latexes and their copolymers for P(BA/MMA)/P(MMA/BA) and P(BA/MMA)/PSt systems in the presence of AHPS

Different poly(methyl methacrylate/n‐butyl acrylate)/poly(n‐butyl acrylate/methyl methacrylate) [P(BA/MMA)/P(MMA/BA)] and poly(n‐butyl acrylate/methyl methacrylate)/polystyrene [P(BA/MMA)/PSt] core‐shell structured latexes were prepared by emulsifier‐free emulsion polymerization in the presence of hydrophilic monomer 3‐allyloxy‐2‐hydroxyl‐propanesulfonic salt (AHPS). The particle morphologies of the final latexes and dynamic mechanical properties of the copolymers from final latexes were investigated in detail. With the addition of AHPS, a latex of stable and high‐solid content (60 wt %) was prepared. The diameters of the latex particles are ～0.26 μm for the P(BA/MMA)/P(MMA/BA) system and 0.22–0.24 μm for the P(BA/MMA)/PSt system. All copolymers from the final latexes are two‐phase structure polymers, shown as two glass transition temperatures (T_gs) on dynamic mechanical analysis spectra. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 86: 3078–3084, 2002     

油田储层敏感性评价实验研究

应用岩心流动实验评价了渤中25-1油田储层的敏感性.结果表明,渤中25-1油田储层存在中等偏强水流速敏感性、中等偏弱水敏感性、弱碱敏感性、无酸敏感性、无盐敏感性.     

Critical evaluation of coupling particle size distribution with the shrinking core model

The shrinking core model (SCM) is widely used to model fluid-solid reactions such as the leaching of metals from minerals. In most cases, however, the particle size distribution (PSD) of the solid material was disregarded. In this paper the erroneous shift in the control regime when neglecting PSD was quantified and the dependence of the shift on the coefficients of variation (CV) and the type of PSD was analysed. By coupling the SCM with a Gamma PSD, it was found that neglecting the PSD would shift the control regime from chemical reaction to inert/ash layer diffusion, when the CV was between 0.7 and 1.2. For a system controlled by liquid film diffusion, neglect of the PSD, would shift the control regime to chemical reaction when CV is between 0.3 and 0.7 or to inert/ash layer diffusion when CV is greater (0.9-1.5). It was therefore postulated that some researchers had unknowingly made invalid conclusions about the control regime due to the neglect of PSD. However, an inert/ash layer diffusion-controlled process was insensitive to the neglect of PSD. When CV<0.3, neglect of the PSD would not cause any erroneous shifts, irrespective of the control regime. Experimental data confirmed the observation. For a given CV, the deviation in the fraction reacted from the mono-PSD increases with CV and decreases with time. The maximum deviation, which occurs at the beginning, is about 10% with a gamma PSD of CV=0.3. The percent deviation is dependent of the type of PSDs. Gamma PSD gives the lowest deviation while Gaudin-Schuhmann results in the largest deviation (maxi. ∼19%, with CV=0.3) in the first half of dissolution process. Log-normal distribution gives a larger deviation than gamma but quickly approaches the latter with time. The deviation for Rosin-Rammler is between log-normal and Gaudin-Schuhmann. For systems with CV less than 0.3, the SCM can be fairly used without considering PSD. When CV is greater than 0.3, particularly in the early stage of a dissolution process with a PSD other than gamma, PSD should be included to avoid substantial errors.     

泡沫夹层结构的模压共固化成型工艺及参数选定

在分析夹层结构的基础上,概述了常用芯材包括铝蜂窝、NOMEX蜂窝和聚甲基丙烯酰亚胺泡沫塑料的性能和特点,介绍了刚性泡沫夹层结构常用的成型工艺,详细阐述了刚性泡沫夹层结构的模压共固化成型工艺及相关参数的选定。     

Toughening of vinylester–urethane hybrid resins through functionalized polymers

Liquid nitrile rubber, hyperbranched polyester, and core/shell rubber particles of various functionality, namely, vinyl, carboxyl, and epoxy, were added up to 20 wt % to a bisphenol‐A‐based vinylester–urethane hybrid (VEUH) resin to improve its toughness. The toughness was characterized by the fracture toughness (K_c) and energy (G_c) determined on compact tensile (CT) specimens at ambient temperature. Toughness improvement in VEUH was mostly achieved when the modifiers reacted with the secondary hydroxyl groups of the bismethacryloxy vinyl ester resin and with the isocyanate of the polyisocyanate compound, instead of participating in the free‐radical crosslinking via styrene copolymerization. Thus, incorporation of carboxyl‐terminated liquid nitrile rubber (CTBN) yielded the highest toughness upgrade with at least a 20 wt % modifier content. It was, however, accompanied by a reduction in both the stiffness and glass transition temperature (T_g) of the VEUH resin. Albeit functionalized (epoxy and vinyl, respectively) hyperbranched polymers were less efficient toughness modifiers than was CTBN, they showed no adverse effect on the stiffness and T_g. Use of core/shell modifiers did not result in toughness improvement. The above changes in the toughness response were traced to the morphology assessed by dynamic mechanical thermal analysis (DMTA) and fractographic inspection of the fracture surface of broken CT specimens. © 2002 Wiley Periodicals, Inc. J Appl Polym Sci 84: 672–680, 2002; DOI 10.1002/app.10392     

两种模具型芯结构的比较

对比两种高冲压开关件型芯拼块结构的优劣和设计要点。     

基于开发者协作关系和信息检索的需求跟踪系统

目前自动化需求跟踪的研究广泛使用文本信息检索技术。然而信息检索会遗漏一些文本不相似但是实际相关的软件制品,导致自动化跟踪的精度不高。针对上述问题,提出利用开发者协作关系来进行优化,研发了基于开发者协作关系和信息检索的需求跟踪系统。该系统在进行需求跟踪时,首先用信息检索推荐与需求文本上相似的代码,然后从代码提交日志中挖掘开发者协作关系,根据开发者协作关系再推荐相关代码,用户根据两次推荐的结果确定正确的需求代码跟踪关系。试验结果表明该系统能够找到信息检索遗漏的需求跟踪关系,能够提高自动化跟踪的准确性,节省跟踪时间。     

水性核（PMMA）／壳（PU）聚氨酯丙烯酸酯杂化乳液的合成研究

合成高Tg低成膜温度的水性聚氨酯丙烯酸酯杂化乳液,研究了合成工艺、—N CO和—O H的比例、丙烯酸酯含量等因素对乳液稳定性和其他性能的影响。     

影视盒面盖注射模具的设计

通过对影视盒面盖的结构及工艺分析,介绍了面盖注射成型模具的设计要点及模具的工作过程。为缩小模具尺寸,简化模具结构,确保面盖外观并降低模具成本,重点探讨了浇注系统、侧抽芯机构、脱模机构等关键部件的设计问题。经生产验证,该模具结构设计合理、可靠,对类似产品的注射模具设计有很好的参考价值。